	Daylight Harvesting: When ambient lux value is lower than preset lux value(30Lux, 50Lux, 80Lux or 120Lux), light on when detect movement and adjust artificial lighting to keep the brightness balancing; When ambient brightness is higher than preset lux value, lamp will still remain off even no movement detected.
	Precondition of Daylight Harvesting: as picture 1. Daylight threshold is on 30Lux, 50Lux, 80Lux or 120Lux. 2. Hold time is on 5s/30s/1min/3min/5min/10min/20min/30min

When ambient lux value is lower than preset lux value(30Lux, 50Lux, 80Lux or 120Lux),

light on when detect movement and adjust artificial lighting to keep the brightness

balancing; When ambient brightness is higher than preset lux value, light off.

When ambient brightness is higher than preset lux level, light will automatically turn off.

Technical date of dc motion sensor:

Operating voltage	10-15VDC
Detection area	25%/50%/75%/100%
Operating current	＜30mA
Output	DIM 0-10V
Stand-by power	<0.5W
Hold time	5s/30s/1min/3min/5min/10min/20min/30min
Daylight threshold	2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/Disable
Stand-by period	0s/10s/30s/1min/5min/10min/30min/+∞
Stand-by dimming level	10%/20%/30%/50%
Operating termperature	-20°C~+60°C
Microwave power	<0.3mW
Microwave frequency	5.8GHz±75MHz

Factory Default Setting: Detection area 100%/ Hold time 5s/ Daylight threshold Disable/Stand-by

period 0s/Stand-by dimming level 10%.

Features of Sensor:

1. Daylight Harvesting Function to make sure the environment at a stable lux value

2. Dual PD to differentiate natural light and LED light

3. Wireless Pins to be easier installed on the LED light board

4. 15m high installation for UFO

5. 5 years warranty.

6. Remote control setting parameters

7. Microwaver Power lower than 0.3mW

8. Totally 11mm thickness, super thin for UFO/linear highbay

9. Module without housing to make it more flexible to be fixed.

Pattern of DC motion sensor:

	Pin setting +12v,GND,DIM+ Wireless Pins to be easier installed on the LED light board
	1.Mounting height,less than 15m/49.2ft (ceiling mounted) 2.Detection range,Max,ø14m/45.92ft (ceiling mounted) 3.Detection angle,30°-150° (without glass)
	The sensor size is (LWH)3433.511mm
	Antenna module:Emit microwave signal,sense the motion of the object Daylight sensor:Inducts the external light sensitivity threshold, controls the lamp switch

Installation precautions of motion sensor:

1. Microwave sensor can be installed in any lamp except the one with full metal shell.

2. The detected surface cannot be shielded by metal objects.

3. Make sure the microwave module is completely exposed outside.

4. The detection surface of the sensor module shall be installed facing the detection area.

5. Should be kept away from the driver to avoid interference generation and lamp flashing.

6. Wiring must be strictly in accordance with the wiring diagram to avoid short circuit.

User Notes

1.Microwave can penetrate walls or glass thinner than 20cm and attenuate if thicker than 20cm.

2. The driver voltage shall be stable and float within 10%.

3. Detection area will be affected by speed of motion, mounting height and movement volume.

4. Conduct test on sunny days without the lampshade which will affect the tested lux value.

Daylight Harvesting Function Bare Board High Altitude Install DC Motion Sensor

Microwave Motion Sensor

BLE Motion Sensor

PIR Motion Sensor

Dimmable Motion Sensor

Motion Sensor ON OFF Switch

UL Version Emergency LED Driver

UL Sensor

DC Motion Sensor

DALI Motion Sensor

IC Sensor

Photocell Daylight Sensor

Motion Sensor Driver

Universal Smart Remote Control

CE Version Emergency LED Driver

UFO Driver

Daylight Harvesting Function Bare Board High Altitude Install DC Motion Sensor

leviton occupancy sensor

ceiling mounted occupancy sensor

occupancy motion sensors